Quick Answer

Frequent Question What front axle is in a 2005 F-250?

Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

Does the F-250 have a solid front axle?

FYI – 2005 on up the only Super Duty front axle that is not the solid axle is the F250 two wheel drive. The F250 4×4 is solid axle.

What axles does my F-250 have?

A Ford Sterling 10.25 axle is a heavy duty, full floating rear axle produced for F-250 and F-350 trucks. It can handle up to 5,000 pounds of gross vehicle weight. In the beginning, Ford used Dana axles in their trucks. Later on, they developed the Sterling 10.25 axle to replace the Dana axles.

What years did Ford use Dana 50?

The solid axle Dana 50 was used in the Ford F-250 and the F-350 from 1999 to 2003. This axle was also the only OEM axle used in Four-wheel drive Ford Excursions. The GAWR of a solid axle Dana 50 is 5000 lbs.

How do I identify my Dana front axle?

Stamped Number on the Axle

To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.

How do I identify my Ford axles early?

The different types of early Ford axles are easy to identify by referring to the picture on the right, which was scanned from an old magazine article that was written by Neal East. The 1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches.

When did Ford stop Twin I Beam?

Twin I-Beams and Twin Traction Beams were utilized on various F-Series trucks until 2002.

What year did Ford stop using straight axles?

Solid front axles, non drive wheels was 1964 the last year. Then in 1988 the Ford F-Super Duty (F450) came out with a solid front axle with 10 lugs per wheel, Dana 80 rear axle with disk brakes.

What new trucks have solid front axles?

Even though we are now down to just three new vehicle models available with a solid front axle in the U.S.—Jeep Wrangler, Ford Super Duty, and Ram heavy-duty trucks (four if you count the über-expensive Mercedes G-class)—we’re still huge proponents of the driven beam axle construction for off-road use.

What front axle is in a 1996 F250 4×4?

Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s.

What front axle is in a 2003 F250?

Dana 60 front axles have been used in FORD F-250 and F-350 4×4 trucks since the mid 70’s. In 2000 Ford F-450 and F-550 4×4 models also used the Dana 60 front axles and starting in 2005 the F-450 and F-550 had the Super 60 front axles.

What years did Ford use Dana 60 front axle?

Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

How do I identify a Dana 60?

It can be identified by its 10-bolt rear cover, which appears to be lying on its side. Each Dana 60 has a build date and bill of materials numbers stamped into the back of the passenger-side axle tube. These numbers are fairly small but they are always on original axles.

How do I know if I have a Dana 50?

The three digit identifier number is usually cast into the upper part of the center section on the passenger side. The number is also on the lower right of the assembly tag (if it is still there). The tag is on the passenger side axle tube.

What year is a Dana 60 kingpin?

The Kingpin Model 60 stayed in the Ford lineup as the only available front drive axle for the F-350 until the end of the 1991 model year. Ford switched to a ball joint Model 60 for the 1992 model year.

How do I know if I have a Dana differential?

Numbers. The Bill of Material (BOM) number is used to identify Dana differentials. The BOM will identify the model number, the gear ratio, the type of differential, and all component parts. Traditional BOM’s are 6 digits followed by 1 or 2 digits and start with the numbers 60 or 61.

How do you tell if you have a Dana 30 or 44?

The quickest way to tell is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle. On a Dana 44 Model, you will see a large castle nut threaded onto a ball joint. For Dana 30 Models, you will see a king pin cap with four bolts threaded down into the top of the knuckle.

What’s the difference between a Dana 44 and a Dana 60?

The Dana 44 axles use u-joints that measure 2.18 inches from snap ring to snap ring. The Dana 60 axle uses u-joints that measure three inches from snap ring to snap ring. The Dana 60 has a larger ring gear, larger axle tubes, larger axle shafts, and overall is much stronger.

How can I tell if my Ford is 8 inch or 9 inch?

Many enthusiasts will tell you to look for the two dimples in the rear cover to determine if the unit is a 9-inch, but this is not always true. Ford also had an 8-inch third-member rear end that had a dimpled cover. The best test of a 9-inch carrier is to try removing the two lower carrier case bolts.

What is Ford axle Code 19?

Answer provided by. Ford axle code 19 tells you what kind of differential and ratio your truck has. Based on Ford axle charts, it looks like you have an F-150 with an open differential and a 3.55 ratio.

How do I know if my Ford is a 9 inch?

Basic ID Ford 9 inch, rear, 8 inch rear end,carrier, center section,
Traction …

What year did Ford go to coil springs?

In part two, we will continue with additional leaf spring interchanges as well as list several rear coil spring interchanges that began when Ford first started using rear coil springs in 1965 Ford and Mercury fullsize cars.

What year did Ford introduce the Twin I-Beam suspension?

The Twin I-Beam arrived in 1965, created at a time when pickups were first becoming civilized transportation. Ford eschewed the idea of adopting dual A-arm suspension for its evolution of the beam suspension rooted in the bones of the Model T.

Is Twin I-Beam a good suspension?

The Twin I-Beam suspension system makes for a smoother ride and better handling than its predecessors. It also helps to reduce tire wear, maintain wheel alignment and decrease the need for front-end maintenance.

Does Ford still use a solid front axle?

Yet slowly, the solid front axle has died out. Aside from the Wrangler, no new passenger vehicle is sold in the U.S. today with a solid front axle. And now we know the new Ford Bronco won’t change that. The Bronco instead opts for an independent front suspension, like pretty much every other truck or SUV out there.

When did Ford go to independent front suspension?

to production, of the new Ford independent front suspension used on its 1980 four-wheel drive light trucks. This four-wheel drive suspension is similar in concept to the well accepted, and proven, Twin- I-Beam independent front suspension used on all Ford two- wheel drive light trucks since 1965.

Does F150 have solid front axle?

Only the F-350 from 85.5 up came with a solid front axle from the factory. All F-150’s, 250’s and 85.5 down 350’s had the TTB independant front suspension (150’s had coil springs while the 250’s and 350’s had leafs). When the new Super Duty’s came out in ’99 both the F-250 and F-350 had solid front axles.

Why are solid axles better for off roading?

“A solid axle setup can improve traction over big bumps and hills as well as gain more torque from the differential as there are fewer parts that power must transfer through,” says aftermarket manufacturer Fab Fours in a comparison between both systems.

What is the advantage of a solid front axle?

A solid axle has less moving parts and is easier to service, with no crossmembers clogging everything up. I also don’t like that the centersection in many new IFS rigs is made of aluminum. Solid-axle centersections are typically cast iron, which is more durable.

What is the best 4×4 of all time?

The 12 Most Capable 4x4s Ever Made

  • 1992-2006 Hummer H1.
  • 1985-95 Suzuki Samurai.
  • 1993-97 Land Rover Defender.
  • 2003-19 Jeep Wrangler Rubicon.
  • 1979-85 Toyota Trucks.
  • 2005-19 Dodge/Ram Power Wagon.
  • 1979-2018 Mercedes-Benz G-Wagen.
  • 2010-19 Ford F-150 SVT Raptor.