Quick Answer

How much HP can 30 spline axles handle?

A 30-spline axle is rated at 6,200 lb-ft, a 31-spline at 7,000, a 33-spline at 8,200, a 35-spline at 9,600, and a 40-spline at 12,000.

How many splines does a 10 bolt have?

Inside the 8.2-inch 10-bolt, the ring-gear bolts have 9/16-inch socket heads with 3/8-24 left-hand threads. The pinion diameter is 1.438 inches, and has 25 splines. Like all Chevy 10-bolts, the axles are retained by C-clips on the inner end of the axle shaft inside the carrier.

How do I know if I have 28 or 31 spline axles?

A 28 spline axle will have a recess in the middle while a 31 spline axle will be solid with just a centering champher (from when it was machined and ground at the factory).

Are more axle splines better?

Higher spline counts gives the axle more surface to transfer the load of the torque from the differential. There is also the side advantage that an axle with more splines will also be physically bigger. At least in most modern axles that use similarly sized spline teeth.

How much HP can 28 spline axles handle?

The should be good up to 350-400 depending on how you launch the car.. Ive seen them break on stock cars with stickey tires. 31 spine for sure…

What is axle spline count?

Spline count dictates the overall diameter of the axle shaft, the larger the axle, the stronger it is.

What size is the pinion nut on GM 10-bolt?

PYN10 – 10-Bolt 8.5″
Pinion Nut (30 Spline Pinion)

Is a 10-bolt rear end posi?

Ten-bolt rears came in both Positraction and non-Positraction versions. Although it would be much cheaper to find one with Positraction already, many aftermarket suppliers can sell you carriers, axles and gears to convert a stock non-limited-slip axle to a Positraction.

Is a 10-bolt Chevy rear end good?

Even though it has been used in every major GM rear-wheel-drive platform, the 10-bolt has a bad reputation for being a low-performance unit. Nothing could be further from the truth. The 10-bolt can handle just about anything you throw at it, as long as you use the right axle, either the 8.5- or 8.6-inch.

How many splines does a Ford 8.8 have?

They’re both 31 splined, but the explorer 8.8 is not the same overall length and the the differential is in a different location between the axle (the truck’s diff is not perfectly in the center of the axle).

What year Mustang has 31 spline axles?

For 2011-2014 Mustangs, both the V6 and 5.0L V8 Mustang were equipped with 31-spline axles.

How many splines does a Ford 8 inch rear end have?

Re: Ford 8in rear end with 31 spline axle shafts

Those parts from a ’68 – 70 Mustang / Cougar should fit a 8″ housing. Also to use 31 spline axles you will need a 31 spline differential that fits an 8″ rear end.

How do you cut axle splines?

How to Cut Axle Splines on a SAJO Indexing Head

Where are Moser axles made?

MADE IN THE USA! Moser Engineering uses its finest alloy for these replacement shafts.

How do you measure a spline shaft?

To determine the spline size of a component (rack and pinion, steering column, and steering box), measure the outside diameter and count the number of splines. If there is a flat spot on the shaft and some of the splines are missing, count halfway around where there are splines and double that number.

How much power can ford 8.8 handle?

Dead stock (31 spline version, which is what the Explorer has) it can handle up to about 400 rwhp as long as you’re not on DR’s or Slicks.

How do you tell how many spline your axle is?

Moser Minute –What is Axle Spline?

What is a spline on a vehicle?

Splines are ridges or teeth on a drive shaft that matches with grooves in a mating piece and transfer torque to it, maintaining the angular correspondence between them.

What component in the final drive assembly are the axle shafts splined to?

It carries the weight of the vehicle. Hub is Directly Connected to axle shaft. Inner end of the axle is splined and supported by final drive unit.

Semi Floating Fully Floating Three Quarter Floating
Bearing
Load + Driving Torque Axle=Driving Torque Bearing=Thrust + Load Axle=Torque+S.Thrust Load =Casing

What size is a GM pinion nut?

1 1/8″ Socket, 7/8″ X 16 Thread.

What size is pinion nut Silverado?

Yukon Gear – Pinion Nut (Part No.

1 1/4″ socket, 7/8″ x 14 thread.

What size is the pinion nut on a 14 bolt?

10.5″ GM 14 bolt truck pinion nut. 1 1/2″ socket, 15/16″ x 16 thread.

How do I know if my 10 bolt is posi?

Locate two lugs, or ears, extending out from the bottom of the gear casing approximately in the 4 o’clock and 8 o’clock position. This will firmly identify the unit as having come with Positraction from the factory.

How do I know if my rear end is posi?

How to tell if your vehicle is open differential or Posi limited slip …

Is posi traction the same as limited slip?

Despite the fact that a lot of folks confuse the terms “posi” or “Positraction” with “limited slip,” the fact is that the two are basically one and the same. Today, all positive traction systems are referred to as limited slip systems.

How much horsepower can a 8.2 10 bolt handle?

Roughly 550 to 600 HP total. No slicks, drag radials. No problems with the 8.2 at all. I used the stock diff., the Auburn would be better.

What year s10 has 8.5 rear end?

According to Chevy High Performance, the 7.5-inch was standard until 1993, when the previously optional 7.625-inch became standard. 1995 and newer S-trucks equipped with the high-output V6 were equipped with the 8.5-inch rear end.

Will a Tahoe rear end fit a Silverado?

No. You shouldn’t try fitting a Silverado differential into a Chevy Tahoe.