Quick Answer

Question: How much does pressure treated deck boards cost?

The average cost of basic pressure treated pine runs about $15-$25 per square foot. Fancier woods will cost a bit more, usually between $25-$30 per square foot. This is the cost for a basic deck.

What is the best size for deck boards?

Width: Six-inch wide boards are ideal in most cases. Four inch wide material takes longer to install, creates more gaps and requires a lot more fasteners—but you can use it. Eight inch wide boards, because of their greater width, have more of a tendency to crack and cup
avoid using them.

Which is better #1 or #2 pressure treated lumber?

#1 material is generally slightly stronger than #2, but I don’t see any reason to go wild and use #1 material on the joists and ledger board on the deck. Additionally, your posts are generally going to be #2 if they are 6×6’s, as #1 is very difficult to come by in SYP timbers.

What sizes do pressure treated boards come in?

Pressure Treated Wood

  • 1″ X 4″ (3/4″ X 3-1/2″)
  • 1″ X 6″ (3/4″ X 5-1/2″)
  • 1″ X 8″ (3/4″ X 7-1/2″)
  • 1″ X 10″ (3/4″ X 9-1/2″)

How many decking boards do I need for a 10×10 deck?

For a 10×10 square deck, you would therefore need twenty-two 10′ deck boards. Dimensions for deck boards can vary depending on the look you want and the deck board type you use. However, the most common is a 5/4” thick by 6” wide deck board of any length.

Why is pressure treated wood cheaper?

An obvious advantage of untreated lumber is its price
it’s much cheaper than treated lumber. Since CCA-treated lumber was taken off the market, new treatment techniques use high levels of copper, which is more expensive. As a result, the cost of treated wood has risen considerably [source: Morrison].

Should deck boards have a gap?

Determining Deck Board Spacing

When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.

Can I use 2×6 for deck boards?

Wood decking is commonly available in 2×6, 2×4, 5/4 x 6, and 5/4 x 4 profiles. 5/4 x 4 and 5/4 x 6 is produced specifically for decking and can be found milled with a radius or bullnose edge. 2×4 and 2×6 are thicker and stronger, but they also tend to be more expensive than a 5/4 board of the same width.

Should deck joists be 2×6 or 2×8?

For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.

What is the best pressure treated wood to use for a deck?

There are a few different types of wood that are commonly pressure treated for decks, but the two most popular are southern yellow pine and douglas fir.

What is the best lumber grade?

Hardwood grades are: FAS (First and Second) is the highest grade of hardwood lumber. It’s usually 6-inches x 8-inches and is 83 percent defect-free on its best side. Select is 4-inches x 6-inches and 83 percent defect free on its best side.

What is the best grade of pressure treated lumber?

The best pressure treated wood for decks is Select, #1 or #2 grade wood. Within all grades, there are planks that will be freer of blemishes and knots and may be called premium. Decking materials such as 2×6 and 5/4×6 frequently are of better-looking #1 and #2 lumber.

How wide is a 2×10 pressure treated?

That means a 2×10 is actually 1 1/2 inch in thickness by 9 1/4 inches.

How long will pressure treated wood last?

How Long Does Pressure-Treated Wood Last? It depends on the climate, the type of wood, its uses, and how well it’s maintained. While pressure treated poles can stay up to 40 years without any signs of rot or decay, decks and flooring might only last around 10 years.

Does pressure treated wood need to be sealed?

Although treated wood is protected against decay and termite attack, the application of a water-repellent sealer to all exposed wood surfaces is recommended upon completion of construction. This sealer will help control surface checking (splitting or cracking) and provide an attractive appearance.

What do I need to build a 8×10 deck?

You will need six 4-by-4 or 6-by-6 pieces of lumber for the posts and four 2-by-10 pieces of lumber that are at least 10 feet long. The latter will combine to make up the two large beams to support the deck. You will also need eight 2-by-6 beams for your joists, which have to be at least 8 feet long.

How many deck boards do I need for a 12×12 deck?

You will need 18 boards of 2-by-6-inch lumber or nine 2-by-10 inch boards to build the joists, also known as the beams. You should purchase an additional 25 percent wood to allow for framing pieces and waste.

How do you stagger deck boards?

A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.

What is a drawback of pressure treated wood?

Chemical risks.

Because this type of decking is treated with chemicals for protection, it can be hazardous when not handled correctly. If the wood is burned, trimmed, or cut, it can release harmful toxins into the air. Pressure-treated wood should not be used for gardens or come in frequent contact with food and water.

Is pressure treated wood good for decks?

In all, pressure treated wood, like anything, has its good qualities and its not-so-good qualities. But, with excellent features such as its resistant to fungal decay and termites as well as its attractive price-point, pressure treated wood is an outstanding choice to use for the construction of your deck.

Is pressure treated wood safe for decks?

First, pressure-treated wood is made by placing the wood into a high-pressure environment, in which a chemical is pressed into the wood that makes it resistant to rot. This means that pressure-treated wood last much longer than untreated wood, making it an ideal choice for decking material.

Should you nail or screw deck boards?

For the decking boards, many agree that screws perform better than nails. They have better tensile strength and will less likely to pop out, which is a common problem in decking. Many also agree that nails are better used for the frame of the decking.

How thick should my deck boards be?

16” on center = Standard for residential decking applications. 12” on center is recommended for a sturdier underfoot feel, when using standard deck board thickness of 1”. 24” on center = Sometimes used for commercial applications such as docks and boardwalks
wider joist spacing requires greater deck board thickness.

Can I use 1×6 for decking?

Width of material: We recommend only 1×4, 5/4×4 or narrower boards. Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.

Can you use 2×8 for deck boards?

Q: Can I use 2×8 treated lumber as deck boards? A: No, that’s a not a good idea. Lumber wider than 6 inches should not be used as a flat surface. Wide, flat boards have a tendency to pool rain water, which can lead to cupping problems.

Should I use 2×4 or 2×6 for deck?

Most builders stick to using a minimum of 2x6s for deck floor joists. If you want to add guardrails and stairs, you need at least 2x10s. 2×4 and 2×6 joists are ideal for ground-level decks without guards.

Is it better to use 2×6 or 5 4 decking?

Many professional deck builders prefer to use 5/4 decking as it is lighter, less expensive, and typically of better quality and appearance than 2×6 decking. Additionally, they also prefer joists spaced at 16” O.C. for strength and durability, regardless of lumber dimensions.

Can a 2×6 span 10 feet?

2-grade 2×6 joists can span up to 10 feet 9 inches from beam to beam when spaced the standard 16 inches apart with a maximum live load of 30 inches per square foot.

How far can a 2×6 decking span without support?

A 2×6 joist can span anywhere between 8′ for Cedar and Redwood to 9′ for Pine and Fir at 16″ OC. 12″ OC yields longer spans, while 24″ OC allows shorter spans.

How far can a 2×10 joist span without support?

How Far Can a 2×10 Beam or Header Span? A 2×10 beam – made up of two 2x10s nailed together – can span up to 11′ without support beneath a deck that is 4′ wide. For a more normal-sized deck, the same beam can span 8′, supporting a deck that is 8′ wide. You can also triple a 2×10 beam.