Quick Answer

Question: How much power can a 1310 u-joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

What size is a 1330 u-joint?

Understanding U-Joints

Series Cross Width Cap Diameter
1310 3.219 (3 7/32”) 1.062 (1 1/16”)
1310BC* 3.219 (3 7/32”) 2 @1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)
1330 3.625 (3 5/8”) 1.062 (1 1/16”)
1330BC* 3.625 (3 5/8”) 2 @ 1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)

What is the difference between 1310 and 1350 U joints?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

Are all 1310 U joints the same size?

This allows you to mate a larger (or smaller) U-joint to the other. For example, you buy a new driveshaft that comes with 1350 weld-in yokes, but your car has 1310-sized yokes for the transmission and rear differential.U-Joint Sizes.

Series Width Cap Diameter
7260 2.125 1.078″
7290 2.622 1.126″

How strong is a 1350 u-joint?

Relying on information provided by the manufacturer of the components, our calculation is that the 1350 series joint is about 37.5-percent stronger than the 1310 series. The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

What is a 1350 u-joint?

Non-cross-drilled Heavy Duty 1350 U Joint

The Thrust washers in each bearing cap is to eliminate metal on metal contact preventing wear and lower overall operating temperature. It is non-greaseable design that is factory lubed with synthetic grease for excellent friction reduction.

What is the size of a 1350 u-joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1350 Series U-Joint 3.625 X 3.625 – 1.188 outside snap ring &gt
1.188 X 1.188 Bearing Cap Diameter.

How do I know what size u-joint I have?

You will need to measure from the edge of one snap ring groove straight across to the edge of the other snap ring groove. For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap.

What is the difference between a 1350 and 1410 u-joint?

1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications.

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

How do you measure a rear yoke?

How to measure yokes and u joints

How do I know if I have a u-joint Spicer?

We recommend using a caliper or micrometer to most accurately measure u-joints. Once you have recorded your measurements, click on the images below to select the appropriate style of u-joint you have. You will then be directed to The Expert to identify your u-joint kit by the dimensions you recorded.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.

What is a conversion u-joint?

Conversion U-Joint 1310 Series To 1350 Series

Normally the larger the U-Joint the stronger it is. The 1310 to 1350 U-Joint Conversion is a mix of two different series specifications on the same u-joint so that that different sized yokes and driveshafts can be connected.

Do they make U-joints with different size caps?

Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.

Do universal joints work at 90 degrees?

It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft. The universal joint is not a constant-velocity joint.

What series is a 369 u-joint?

Fitment U-Joint moog-369 fits these vehicles: AMC Ambassador 1967 thru 1974. AMC American 1968 thru 1968. AMC AMX 1968 thru 1980.

What is the speed ratio of a universal joint?

It turns out that a moment component normal to the shaft is unavoidable. Introduction THE UNIVERSAL joint is a mechanism for transmission of torque and angular velocity at a mean transmission ratio of 1 : 1, with a variable angle between the shafts.