Quick Answer

Question: What is the difference between a 1350 and 1410 U joint?

1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications.

What is the difference between 1410 and 1415 U joint?

READ THIS: The 1415 series AAM universal joint is just . 007 NARROWER than the Spicer 1410 series. The bearing cap diameter is exactly the same for both. The two are not interchangeable and great care should be taken to be sure of the manufacturer of your driveshaft before ordering and installing any universal joints.

What size is a 1410 U joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1410 Series U-Joint 4.188 X 4.188 – 1.188 outside snap ring &gt
1.188 X 1.188 Bearing Cap Diameter.

How strong is a 1350 U joint?

Relying on information provided by the manufacturer of the components, our calculation is that the 1350 series joint is about 37.5-percent stronger than the 1310 series. The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

What is the strongest U 1310 joint?

1310 Series Spicer MAINTENANCE FREE Universal Joint

Use this u-joint when you want the most strength out of a 1310 series universal joint. Stronger than a greaseable u-joint.

What size u-joint do I need?

For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion.U-Joint Sizes.

Series Width Cap Diameter
1350 3.622″ 1.188″
1410 4.188″ 1.188″
1415 4.178″ 1.187″
1480 4.187″ 1.375″

How wide is a 1350 U joint?

Understanding U-Joints

U-Joint Series Width Center/Center Torque Specifications
1310/1330 1.416 in. 14-17 Ft-Lbs
1330 BC* 1.590 in. 14-17 Ft-Lbs
1350/1410 1.666 in. 20-24 Ft-Lbs

What size is a 1330 U joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1330 Series U-Joint 3.625 X 3.625 – 1.062 – 1.125 outside snap ring &gt
1.062 X 1.062 Bearing Cap Diameter.

What is the difference between a 1310 and 1350 U joint?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

How are U-joints measured?

You will need to measure from the edge of one snap ring groove straight across to the edge of the other snap ring groove. For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap.

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

How much torque can 1310 u-joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

What is AU joint Spicer?

Spicer Extreme™ U-Joints: for Off-Road Use Only

Featuring an SAE-4340 nickel chromoly steel cross with an enlarged trunnion diameter for added strength, these u-joints are virtually indestructible.

Do they make U-joints with different size caps?

Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.

What is a conversion u-joint?

Conversion U-Joint 1310 Series To 1350 Series

Normally the larger the U-Joint the stronger it is. The 1310 to 1350 U-Joint Conversion is a mix of two different series specifications on the same u-joint so that that different sized yokes and driveshafts can be connected.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.

What are U-joints used for?

Universal joints allow drive shafts to move up and down with the suspension while the shaft is moving so power can be transmitted when the drive shaft isn’t in a straight line between the transmission and drive wheels. Rear-wheel-drive vehicles have universal joints (or U-joints) at both ends of the drive shaft.

How do you measure a drive shaft u-joint?

How to measure yokes and u joints