Quick Answer

Question What size is a 1350 on a yoke?

What is a 1350 yoke?

The forged 1350 steel pinion yokes are designed for Spicer 1350 series universal joints, forged for maximum strength, precision machined, heat treated for toughness, built with U-joint-style joint retainers, and available with the appropriate nuts, washers and u-bolt.

How much power can a 1310 U-Joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

How much torque can a 1350 U-Joint handle?

The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

What size is a 1310 u-joint?

1310 Series U-Joint 3.219 X 3.219 – 1.062 – 1.125 outside snap ring.

Are all 1310 U-joints the same?

This allows you to mate a larger (or smaller) U-joint to the other. For example, you buy a new driveshaft that comes with 1350 weld-in yokes, but your car has 1310-sized yokes for the transmission and rear differential.U-Joint Sizes.

Series Width Cap Diameter
7290 2.622 1.126″

What is the difference between a 1350 and 1410 U joint?

1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications.

How do I know what size U joint?

For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap. With these dimensions, it will be easy to identify what series of U-joint that you have.

What is the yoke on an axle?

The slip yoke is an important component of any drive shaft assembly. The slip yoke assembly (pictured on the right) is what allows drive shafts and PTOs to flex or “slip” with their given application. The slip yoke is also essential for allowing u-joints to rotate properly with the drive shaft.

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

What is a 1344 u-joint?

QU40758 Greaseable S44, AAM 1344, or 3R Series Driveshaft Universal Joint for many Dodge and General Motors front or rear driveshafts from the mid 1970’s to current. QU40758 is a hot-forged, alloy steel, greaseable u-joint with nitrile rubber seals. You will find this u-joint used in both CV and non CV applications.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.

How many U-joints do I need?

That’s why it’s a good idea to check the u-joints at every oil change. A typical rear wheel drive vehicle has 2 or 3 u-joints. Some vehicles with a long wheel base, such as buses, have 3 or more u-joints. The more u-joints a vehicle has, the higher the chance a u-joint will fail.

What size is a 1330 u-joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1330 Series U-Joint 3.625 X 3.625 – 1.062 – 1.125 outside snap ring &gt
1.062 X 1.062 Bearing Cap Diameter.

Do universal joints work at 90 degrees?

It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft. The universal joint is not a constant-velocity joint.

What is the advantage of a double cardan joint?

The real benefit to a C. V. (double cardan) drive shaft is smoother operation at higher operating angles and longer life. The C.V. assembly works by intersecting the joint angles at the center pivot point and delivering a smooth rotational power flow or surface velocity through the drive line.

What series is a 369 u-joint?

Fitment U-Joint moog-369 fits these vehicles: AMC Ambassador 1967 thru 1974. AMC American 1968 thru 1968. AMC AMX 1968 thru 1980.

How do you measure a driveshaft yoke?

Place one end of the tape measure near the tip of the slip yoke. Place the other end of the tape measure near the middle of the slip yoke’s u-joint. Note the measurement on the tape measure to determine the length of the slip yoke.

What is a rear yoke?

Definition- This is a piece of fabric that connects the back of a garment to the area across the back shoulders, allowing the garment to lie flat while following the reliefs of the body, ensuring correct drape and appearance.

How do you tighten a yoke nut?

With the rear wheels off the ground tighten the nut up snug but don’t over do it. Put the torque wrench on the nut and apply force it like you are tightening the nut and note the reading as the pinion is rotating. The normal process is to check-tighten-check-tighten and so on until the preload spec is reached.

How do you measure a rear yoke?

How to measure yokes and u joints