Quick Answer

Quick Answer: How do you fix a P0011 code?

What repairs can fix the P0011 code?

  1. Resetting the fault codes and performing a road test.
  2. Changing the oil and filter to the proper oil viscosity for the engine specifications.
  3. Repairing or replacing the wiring to the camshaft oil control valve for bank 1 intake camshaft.

Is P0011 intake or exhaust?

When trouble code P0011 is set, it means that the intake camshaft in Bank 1 is more advanced than the engine computer has told it to be.

What causes P0011?

The camshaft timing is off. The valve control solenoid is stuck open. The valve control solenoid system has faulty or damaged wiring. The oil is too viscous and flow to and from the camshaft’s phasers is restrictive.

How much does it cost to fix a P0011 code?

If the problem goes undetected or untreated for too long, sludgy oil can build up in your engine and block the passage to the Oil Control Valves (OCV). Unfortunately, if that happens, you’ll probably need to replace your engine, which will likely cost somewhere around $3000 to $4000.

Will an oil change fix P0011?

How Much Does It Cost To Fix Code P0011? A basic oil change (about $30 to $50) will not be necessary if the engine is relatively new or has low mileage. Dirty oil is the most common cause of the P0011 OBD2 Trouble Code.

How do I fix code P0022?

What repairs can fix the P0022 code?

  1. Resetting the fault codes and performing a road test.
  2. Replacing the oil and filter using the proper oil viscosity for the engine.
  3. Repairing or replacing the wiring or connection to the camshaft oil control valve (OCV)

What is code P0017?

P0017 is the OBD-II generic code indicating that the crankshaft and camshaft position sensor for bank 1 exhaust camshaft do not correlate signals with each other.

What is code P0021 mean?

What Does Code P0021 Mean? P0021 definition: Intake Camshaft Position Timing- Over-Advanced (Bank 2) Issue Severity: MODERATE– Extended driving with this code can cause internal engine damage. Repair Urgency: Get this code fixed as soon as possible.

What can cause a P0021?

What are the Possible Causes of the P0021 Code?

  • Faulty valve variable timing actuator.
  • Worn or damaged timing chain.
  • A failed timing chain tensioner or guide.
  • Low engine oil.
  • Stuck or defective timing valve control solenoid.
  • An issue with the PCM, such as software in need of an update.

Can I drive with a P0011 code?

Driving with a P0011 code in your car is possible, though not advisable. Do not drive with it until you repair it because it can cause severe damage to your car engine components. By ignoring the P0011 error code in your car, the vehicle will emanate several drivability issues.

Where is the camshaft actuator located?

A camshaft actuator is a mechanical or electronic device that is mounted on the camshaft gear.

How do I fix code P0013?

What repairs can fix the P0013 code?

  1. Resetting the fault codes and performing a road test.
  2. Repairing or replacing the wiring to the exhaust camshaft oil control valve for bank 1.
  3. Replacing the camshaft oil control valve for bank 1 exhaust camshaft.
  4. Replacing the ECM.

How is P0171 diagnosed?

How does a mechanic diagnose the P0171 code?

  1. Assuming that no other trouble codes exist, a mechanic may diagnose the P0171 code by checking the engine for vacuum leaks with a vacuum gauge.
  2. The fuel pressure sensor and MAF sensor (mass air flow) will also be checked with a fuel pressure gauge.

What does exhaust camshaft position Timing Over Advanced mean?

The exhaust camshaft has advanced too much when the ECM has commanded the camshaft to retard to a lower timing level. The oil viscosity is excessive causing the passages to become clogged, causing oil flow to and from the camshaft phasers to be restrictive. The camshaft phaser is seized in the advanced position.

Can you drive with a P0014 code?

While you can still drive around with P0014 registered issues, please don’t do it. Driving with it will cause hard starting, erratic idling, stalling, poor engine performance, and increased fuel consumption. Again, if a lousy VVT control solenoid triggers the issue, it may cause other related components to fail.

Can you drive with a P0022 code?

What Does Code P0022 Mean? Issue Severity: SEVERE – Extended driving with this code can cause internal engine damage. Repair Urgency: Fix this code immediately. Diagnosis: This trouble code severely impacts the drivability of your vehicle.

How do I fix code P0345?

What repairs can fix the P0345 code?

  1. Replacing the crankshaft position sensor.
  2. Repairing or replacing damaged wiring.
  3. Repairing loose connections.
  4. Identification and repair of fluid leaks.

Where are the VCT solenoid located?

The variable valve timing solenoid is located at the front of the engine, typically near the front of the valve cover.

What is P0008 code?

What Does the Code P0008 Mean? P0008 is the result of a test run by the engine control module to check for misalignment between the camshafts in engine bank one and the crankshaft. The misalignment for this code would be at an idler sprocket in the bank or at the crankshaft.

What is code P0014?

What Does Code P0014 Mean? P0014 definition: Exhaust Camshaft Timing- Over-Advanced Bank 1. Issue Severity: SEVERE – Stop driving immediately. Repair Urgency: Fix this code immediately (same-day if possible) to avoid damage to multiple internal engine components.

What is code P0024?

What the P0024 code means. P0024 is the OBD-II generic code indicating the Engine Control Module (ECM) has determined that the bank 2 exhaust camshaft is in a more advanced position than what the ECM expected. The over advanced position can be during the retarding or advancement phase of the camshaft timing.

What is code P0016?

What does the P0016 OBD-II code mean? When a P0016 OBD-II generic code is triggered, it alerts the driver that the camshaft position sensor (CMP) for bank 1, which detects camshaft rotation, is not corresponding to the crankshaft position sensor (CKP) signal.

What is code P0020 mean?

P0020 is the OBD-II generic code indicating that the engine control module (ECM) has determined that the bank 2 intake camshaft Oil Control Valve (OCV) has an open or short circuit. This happens during one drive cycle.

What is code P0340?

The ECM uses this information to control ignition spark and fuel injector timing. When the trouble code P0340 is set, the ignition spark and fuel injector timing fail due to the engine not knowing when to fire these components.

What is code P0023?

P0023 is the OBD-II generic code indicating the Engine Control Module (ECM) has determined that the bank 2 exhaust camshaft Oil Control Valve (OCV) has an open or short circuit. This happens during one drive cycle.

How do I fix code P0018?

What repairs can fix the P0018 code?

  1. Repair or replace the wiring to the camshaft sensor on bank 2.
  2. Repair the wiring or connection to the camshaft OCV.
  3. Replace the camshaft OCV or the camshaft sensor for bank 2 camshaft.

What is P0012 code mean?

P0012 is an OBD-II generic trouble code which indicates a vehicle’s ECM (engine control module) has detected the intake camshaft timing on Bank 1 (number 1 cylinder side of engine) does not correspond with the intake camshaft timing (in degrees) which the ECM expected to find
the camshaft timing is over-retarded, …