Quick Answer

Quick Answer How much power can a 1310 u-joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

What is the difference between a 1350 and 1410 u-joint?

1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications.

What size is a 1410 u-joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1410 Series U-Joint 4.188 X 4.188 – 1.188 outside snap ring &gt
1.188 X 1.188 Bearing Cap Diameter.

What is the difference between 1410 and 1415 u-joint?

READ THIS: The 1415 series AAM universal joint is just . 007 NARROWER than the Spicer 1410 series. The bearing cap diameter is exactly the same for both. The two are not interchangeable and great care should be taken to be sure of the manufacturer of your driveshaft before ordering and installing any universal joints.

Are all 1310 U joints the same size?

This allows you to mate a larger (or smaller) U-joint to the other. For example, you buy a new driveshaft that comes with 1350 weld-in yokes, but your car has 1310-sized yokes for the transmission and rear differential.U-Joint Sizes.

Series Width Cap Diameter
7260 2.125 1.078″
7290 2.622 1.126″

What is the difference between 1310 and 1350 U joints?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

What size is a 1310 u-joint?

Understanding U-Joints

Series Cross Width Cap Diameter
1310 3.219 (3 7/32”) 1.062 (1 1/16”)
1310BC* 3.219 (3 7/32”) 2 @1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)
1330 3.625 (3 5/8”) 1.062 (1 1/16”)
1330BC* 3.625 (3 5/8”) 2 @ 1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)

Do universal joints work at 90 degrees?

It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft. The universal joint is not a constant-velocity joint.

How much torque can a 1350 u-joint handle?

The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

How do I know if I have a Spicer U-joint?

Identifying the Driveshaft Series and U-joints | Spicer Garage

How do I know what size U-joint I have?

You will need to measure from the edge of one snap ring groove straight across to the edge of the other snap ring groove. For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap.

How is UJ measured?

How to measure yokes and u joints

Do they make U-joints with different size caps?

Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.

Do U-joints have part numbers on them?

On all U-joint styles, the measured dimension should be slightly less than the dimensions you’ll use to look up the part number. Make sure to take note of the type and location of grease fittings and to write down your measurements.

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

What is a 1344 u-joint?

QU40758 Greaseable S44, AAM 1344, or 3R Series Driveshaft Universal Joint for many Dodge and General Motors front or rear driveshafts from the mid 1970’s to current. QU40758 is a hot-forged, alloy steel, greaseable u-joint with nitrile rubber seals. You will find this u-joint used in both CV and non CV applications.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.

Do FWD cars have U-joints?

Front-wheel drive (FWD)

Instead of having a long driveshaft like on a rear-wheel vehicle, all the drivetrain components are in the front of the vehicle. Rather than using universal joints, this setup uses constant velocity (CV) joints.

How much does it cost to replace U-joints?

The Best in Auto Repair

The average cost for u-joint replacement is between $240 and $288. Labor costs are estimated between $108 and $137 while parts are priced between $131 and $151. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

How long do u-joints last on a truck?

In most cases, you have to grease your u-joints every 5,000 miles or so. When you fail to service your u-joints on a regular basis, they will fail. You don’t have to worry about this problem with maintenance free u-joints. Misalignment: This happens when you change the vehicle’s ride height.