Quick Answer

Quick Answer: How much torque can a 1350 u-joint handle?

The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

How much torque can 1310 u-joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

What is the difference between 1330 and 1310 u-joint?

1330 joints use a larger body than the 1310 joint but the same-size trunnions and caps. They are often found in 3⁄4-ton trucks and allow more angularity than 1310 joints but are only marginally stronger. 1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps.

What size u-joint do I need?

For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion.U-Joint Sizes.

Series Width Cap Diameter
1350 3.622″ 1.188″
1410 4.188″ 1.188″
1415 4.178″ 1.187″
1480 4.187″ 1.375″

What is the difference between 1310 and 1350?

Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

What is the strongest U 1310 joint?

1310 Series Spicer MAINTENANCE FREE Universal Joint

Use this u-joint when you want the most strength out of a 1310 series universal joint. Stronger than a greaseable u-joint.

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

What is 1350u joint?

Standard u-joints sizes are classified by series, with each series having specific cap diameter and overall joint width. Typically speaking, a higher series number translates to a stronger joint.Understanding U-Joints.

Series
Cross Width
Cap Diameter
Spicer P/N

Does drive shaft diameter matter?

The longer and smaller (diameter) a driveshaft is, the lower its critical speed. Critical speed is felt as excessive vibration that could cause the unit to fail.

Do universal joints work at 90 degrees?

It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft. The universal joint is not a constant-velocity joint.

Do they make u-joints with different size caps?

Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.

What size is a 1330 u-joint?

Driveshaft and Driveline Parts &gt
Universal Joints &gt
U-Joints BY SIZE &gt
1330 Series U-Joint 3.625 X 3.625 – 1.062 – 1.125 outside snap ring &gt
1.062 X 1.062 Bearing Cap Diameter.

How far should yoke stick out of transmission?

CC: How much should the front yoke of a driveshaft engage the output shaft of the transmission? DD: The slip yoke should be able to go into the tailshaft of the transmission so the barrel is fully inside the seal. Then, pull out the yoke 1 inch. This is the correct amount of spline contact for the slip yoke.

Is an aluminum driveshaft worth it?

The Advantages

Typically, switching to an aluminum shaft will mean reducing the weight by anywhere from 10 to 20 pounds. This decrease in weight benefits the engine as well, as weight is magnified when it needs to rotate, just as driveshafts do. The less weight that needs to be rotated, the easier it is on your engine.

How long can a drive shaft be?

A one-piece steel shaft can’t be longer than 72″ from the center of the u-joint at one end to the center of the u-joint at the other end. If you have need for a driveline to be longer than 72″, it can be converted to a 2-piece driveshaft or built using aluminum tubing.

What is AU joint Spicer?

Spicer Extreme™ U-Joints: for Off-Road Use Only

Featuring an SAE-4340 nickel chromoly steel cross with an enlarged trunnion diameter for added strength, these u-joints are virtually indestructible.

How are U-joints measured?

You will need to measure from the edge of one snap ring groove straight across to the edge of the other snap ring groove. For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap.

What is the best driveline angle?

Most driveline companies recommend operating angles of 3° or less for maximum u-joint life. There should be a minimum of ½° to allow the needles to rotate. The higher the operating angle, the more likely your vehicle will develop a vibration at high driveshaft speeds.

What should my transmission angle be?

According to Currie, the average car crafter should strive for between 1 and 3 degrees between the tailshaft of the transmission and driveshaft, and 1 to 3 degrees between the driveshaft and pinion. Furthermore, the two angles should be nearly equal (between 1 and 3 degrees), but always opposite (see crude diagram).

What angle should an engine be installed at?

Commonly, engines are installed at an angle that results in the carb mounting pad being level. That is typically about 3 degrees down in back.

What series is a 369 u-joint?

Fitment U-Joint moog-369 fits these vehicles: AMC Ambassador 1967 thru 1974. AMC American 1968 thru 1968. AMC AMX 1968 thru 1980.

What is the advantage of a double cardan joint?

The real benefit to a C. V. (double cardan) drive shaft is smoother operation at higher operating angles and longer life. The C.V. assembly works by intersecting the joint angles at the center pivot point and delivering a smooth rotational power flow or surface velocity through the drive line.

What is a CV driveshaft?

Constant Velocity, or CV drive shafts, are a unique type of drive shaft that allows for continual rotational velocity through a variable angle without a significant increase in friction or play. The most common applications for a CV drive shaft are: Front-wheel drive vehicles. All-wheel drive vehicles.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.