Quick Answer

Quick Answer: Is there such a thing as a 6 lug 14 bolt?

ORU now offers a hybrid six-lug 14-bolt axle that’s complete drum-to-drum with Superior Axle gears, shafts, and a Detroit Locker for $2,995. It will hold up to all the power you can make, and there is no need to buy new wheels.

Is a GM 14 Bolt good?

GM’s Strong &amp
Plentiful Axle

When it comes to strength, value, and vast availability, the full-float 14-bolt rear axle from General Motors is about as good as it gets.

What is a GM 14 bolt rear axle?

The General Motors Corporate 14 bolt is a heavy duty, full floating rear axle used in 1973 to 2001 Chevrolet and GMC pickups. It is not to be confused with the smaller, semi floating 14 bolt axle, which uses a 9.5″ ring gear and is built for 3/4 ton applications.

How do I identify a 14 bolt rear end?

GM 14 Bolt Differential Explained – How to Identify

Is a 14 bolt semi float good?

Still, the 14-bolt semi-float is a solid axle for a lot of applications. Compared to a GM 10-bolt axle (for example), a semi-float 14-bolt is a nice upgrade. You can spot a semi-float 14-bolt axle by counting the lugs (if it’s a six lug wheel, it’s a semi-float), or by looking at the wheel surface.

Is a 14 bolt A 1 ton axle?

The 14-Bolt Is The Ford 9-Inch Of 1-Ton Trucks

Every diesel-powered pickup sold in the United States for the last 10 years has a full-floating rear axle.

Are all 14 bolt carriers the same?

14 Bolts Have a Carrier Break

For manufacturing and performance reasons, manufacturers often change the carrier at a midpoint in a gear ratio range to deal with the smaller and smaller pinion and the thicker ring gear. This means that there are two different carriers that come in a 14 bolt axle.

Is a 14 bolt rear end a Dana 60?

The 14 Bolt and Dana 70 axles are Heavier Than a Dana 60

The 14 bolt axle and the Dana 70 weigh more partly because they have 3.5″ axle tubes, which are slightly larger than the 3 3/8″ tubes found on many Dana 60s. This helps the tubes resist bending when side loaded by large tires.

Are all 14 bolt rear ends the same?

Over the years, there have been millions of 14 bolt axles produced. And, of course, they weren’t all the same. GM 14 bolt axles were available in semi-float and full-float versions, and there are two types of hubs found on 14 bolt axles. Also, two different types of drums were used.

How wide is a GM 14 Bolt axle?

GM 14-Bolt Specs

Pinion Bearing Preload (Inch lbs) 25 – 35 (new bearings) 5-15 (reused bearings)
Pinion diameter 1.750″ x 30 splines
Carrier Break 4.10 / 4.56
Approximate Weight (lbs) 550 with brake drums 450 without brake drums
Width – WMS-WMS (inches) SRW/DRW 67″ C&C DRW 63″

What trucks have a 14 bolt rear end?

The 10.5″ Corporate 14 Bolt Differential is a heavy duty differential found on many 1973-2013 Chevrolet and GMC trucks and SUVs, as well as certain versions of the Cadillac Escalade. Additionally, this differential is found on Chevrolet Express and GMC Savanna vans produced from 1973 to current day.

How do I tell what gear ratio my 14-bolt is?

Carefully count the number of full revolutions the driveshaft makes. This is your gear ratio. In other words, if the drive shaft turns 3 &amp
3/4 turns, you probably have a 3.73 gear ratio.

How wide is a Chevy 14-bolt rear end?

14 Bolt Axle Dimensions

WMS to WMS width Axle tube diameter
SRW 68″ 3.375″
DRW 72″ 3.5″
C&C DRW 63.5″ 3.5″
SRW Van 70″ 3.5″

What is the strongest rear end?

Dana 60 Rear End Assemblies

If you want a big brute of a rear end under your car, look no further than a Dana 60. Even in the heyday of muscle cars, Dana 60 rear differentials were renowned for their strength, along with their difficulty to locate.

What is a full float rear-end?

In a full-floating axle, the axle is not attached to the axlehousing at all
it is allowed to “float” inside the axlehousing
. A tubular shaft is mounted to the end of the housing and acts like your front spindle, only it is hollow to allow the axle to meet up with the wheel assembly.

What is a Dana 60 rear-end?

The Dana 60 is a Salisbury-type rear-end, meaning the differential carrier removes from the rear of the axle instead of the front. It can be identified by its 10-bolt rear cover, which appears to be lying on its side.

How much torque can a Dana 80 handle?

It’s a full-float unit with 11.25-inch ring gear diameter
1.625-inch (minimum diameter) 37-spline pinion shaft
11/2-inch-diameter, 35-spline axleshafts
and a 4-inch axletube diameter. It has an 11,000-pound gross axle weight rating and a continuous manufacturer’s output torque rating of 2,500 lb-ft.

What is the difference between SRW axle and a DRW axle?

SRW stands for Single Rear wheel and DRW stands for Dual Rear Wheel. Ford trucks like the Super Duty F-350 are available in both SRW and DRW variations, so you can pick the truck that best suits your lifestyle.

What did Dana 60 axles come in?

The Dana 60, a heavier-duty axle than the Dana 44, was first used in the 1950s. It was the axle of choice under countless Dodge, Ford, GM, Studebaker, IH and Jeep 3/4-ton and 1-ton fullsize trucks, as well as Ramchargers and Trail Dusters with the 440ci V-8, and some heavy-duty 1/2-ton Ford and IH trucks.

What vehicles came with a high pinion Dana 60?

The Dana/Spicer Model 60 is an automotive axle manufactured by Dana Holding Corporation and used in OEM pickup and limited passenger car applications by Chevrolet, Dodge, Chrysler, Jeep, Ford and Land Rover.

What are Dana axles?

The Dana/Spicer Model 44 is an automotive axle manufactured by Dana Holding Corporation and is used extensively among automobile manufacturers and in the automotive aftermarket area as well. The Dana 44 was first manufactured in the 1940s and is still being manufactured today, both front and rear axle variants.

Are front and rear ring and pinion the same?

These sets are exactly the same. But when the rig is driven forward the pinion is putting pressure on the drive side of the ring gear in the rear and on the coast side of the ring gear in front.

What does a Dana 80 come in?

ID A Dana 80 Rear Axle in Chevy, Dodge Ram, or Ford Truck IDN-126. Was: Dana 80 Rear Axles have been in production since the 1988 Model Year. They have been used in Chevy/GMC 1992-2002 , Dodge(1994-2002), and Ford (1988-current) trucks vans, and motorhome chassis.

How do I know what axle ratio I have?

Method 1: Count the number of teeth on the ring gear and the pinion. Divide the number of the ring gear’s teeth by the number of the pinion’s teeth. This will give you the axle ratio.

What is the difference between a full floating and semi floating axle?

The axle shaft also rides on a large roller or ball bearing out at the end of the axle housing. For a full-floating system, the axle shaft only serves to transmit the rotational torque from the differential out to the wheel. It does not carry the weight of the vehicle as a semi-floater does.