Quick Answer

Quick Answer What axles are in a 2005 F250?

Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks. Each axle is built with a Bill of Material (BOM) Tag affixed to the differential cover by two cover bolts.

How wide are 05 super duty axles?

The 84.74-inch-wide axle (an F-350 front axle is 69.8 inches wide) was designed for the ’05-and newer F-450 and F-550 Super Dutys, where it’s rated to support 7,000 pounds of gross axle weight (GAWR) and cope with more than 600 lb-ft of engine torque.

What rear axle is in a 2005 F350?

The rear axle on the F350 is a Dana 80. Both have the same Dana 60 up front.

What axle does a F250 have?

For the 2017-2019 F-250, the front axles are still a 35 spline Dana 60 axle. In the back, the 10.5” is still standard but trucks fitted with the Heavy Duty Towing Package are set up with a Dana M275 axle.

What trucks have Dana 60 front axles?

The Dana 60, a heavier-duty axle than the Dana 44, was first used in the 1950s. It was the axle of choice under countless Dodge, Ford, GM, Studebaker, IH and Jeep 3/4-ton and 1-ton fullsize trucks, as well as Ramchargers and Trail Dusters with the 440ci V-8, and some heavy-duty 1/2-ton Ford and IH trucks.

Is the Dana 50 a good axle?

In fact, the Dana 50 and 60 high-pinion Super Duty axles have more in common than you might realize. As you may infer from its name, the Dana 50s overall size and strength rest between that of a Dana 44 and Dana 60. For those looking to run up to a 37-inch tire, the Dana 50 is well-suited.

What is the difference between a Dana 60 and a Super 60?

The Dana Super 60 is an upgraded version of the Dana 60 axle. Differences in the Dana Super 60 versus the regular Dana 60: Larger and thicker diameter steel tubes (3.75 inches diameter and ½ in thick) Larger ring and pinion which increase the contact area and overall strength.

When did the F250 get a Dana 60?

The 1999 through 2003 model year F250/350 had Dana 50 Axles. The 2004 and up F250/350’s had Dana 60 axles.

What’s the difference between high pinion and low pinion?

A low-pinion axle positions the pinion below the centerline of the axle, while a high-pinion axle places the pinion above the centerline of the axle.

How do I identify my rear axle F350?

Precise identification of Excursion and 1999-2004 F-250/F350 axles is by axle tags found on the differential cover and/or a decal on the right axle beam. Ford assigns an axle code to each axle configuration. A typical Axle Code will have 5 digits and look something like this: V414C.

Is Sterling 10.5 full-float?

The 10 1/2-inch (commonly referred to as the “Sterling 10 1/2”) is a full-float axle with disc brakes found in 1999-2010 Ford Super Duty F-250 and Super Duty F-350 trucks. It weighs in at approximately 333 pounds in single rear-wheel versions. The ring gear diameter and pinion shaft length are both 10 1/2 inches.

Is Sterling 10.5 a good axle?

At the end of the day, the Sterling 10.5 isn’t a bad rear axle, it simply has a weak spot that needs to be addressed. We’re even willing to go out on a limb and say it’s one of the best-value full-float axles available. Well, next to the GM 14-bolt, of course.

What front axle is in a 1996 f250 4×4?

Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s.

What front axle is in a 97 f250?

Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s.

How do I identify Dana axles?

Stamped Number on the Axle

To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.

Is Dana 44 better than 60?

Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.

Is a Dana 60 a 1 ton axle?

The Dana 60 and Dana 70 are two heavy-duty variants in the Dana axle line, and are typically found in 3/4 ton and 1 ton pickup trucks.

How do you tell if you have a Dana 60 or 70?

Luckily, it’s pretty easy to tell which axle you have. The original factory axles in a Full Float Dana 60 always have 30 splines or less. If you pull an axle shaft out of your Dana and it has 33 or 35 splines, then you probably have a Dana 70.

Which is stronger Dana 44 or Dana 50?

Dana 50’s were made as front axles only. The Dana 50 has a “50” cast into the housing and is regarded to have more strength than a Dana 44, but not as much as a Dana 60. It was only produced in a reverse cut gear set aka a high pinion.

How do you tell if I have a Dana 50 or 60?

The three digit identifier number is usually cast into the upper part of the center section on the passenger side. The number is also on the lower right of the assembly tag (if it is still there). The tag is on the passenger side axle tube.

What years did Ford use Dana 60 front axle?

Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

What is a Dana 44 axle?

The Dana/Spicer Model 44 is an automotive axle manufactured by Dana Holding Corporation and is used extensively among automobile manufacturers and in the automotive aftermarket area as well. The Dana 44 was first manufactured in the 1940s and is still being manufactured today, both front and rear axle variants.

Is a 14 bolt A 1 ton axle?

The 14-Bolt Is The Ford 9-Inch Of 1-Ton Trucks

Every diesel-powered pickup sold in the United States for the last 10 years has a full-floating rear axle.

What is Dana 30 axle?

The Dana/Spicer Model 30 is an automotive axle manufactured by Dana Holding Corporation. It has been manufactured as a beam axle and independent suspension axle with several versions.

What year is a super Dana 60?

Description. Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

What year is a Dana 60 kingpin?

The Kingpin Model 60 stayed in the Ford lineup as the only available front drive axle for the F-350 until the end of the 1991 model year. Ford switched to a ball joint Model 60 for the 1992 model year.

What gear ratio is a Dana 60?

The Dana 60 carrier split is at 4.56:1-and-up ratio gears.

What are reverse cut gears?

The term “reverse cut” refers to the direction of the spiral cut in the ring gear, which is opposite that of a standard cut ring gear: Contrary to popular belief, it does not run backwards or in reverse.

Is Ford 9 inch high pinion?

This is why Ford, Toyota, and Jeep have used high-pinion differentials in the front of their vehicles for decades. Meanwhile the Ford 9-inch is incredibly light and strong, making it the axle of choice for everything from drag racing to circle track to NASCAR.

What is a high pinion Dana 44?

High pinion means the pinion is above the center line of the ring gear and the way the gears are cut they drive on the drive side of the gear insted of the coast side making them stronger.