1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps. 1410 joints use a wider body but the same-size caps as a 1350 joint, making them perfect for high-horsepower, high-angle applications.
How wide is a 1410 U joint?
4.188 inches wide
|Country of Origin||United States|
What is the difference between 1410 and 1415 U joint?
READ THIS: The 1415 series AAM universal joint is just . 007 NARROWER than the Spicer 1410 series. The bearing cap diameter is exactly the same for both. The two are not interchangeable and great care should be taken to be sure of the manufacturer of your driveshaft before ordering and installing any universal joints.
How strong is a 1350 U joint?
Relying on information provided by the manufacturer of the components, our calculation is that the 1350 series joint is about 37.5-percent stronger than the 1310 series. The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.
What size u-joint do I need?
For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion.U-Joint Sizes.
What is the strongest U 1310 joint?
1310 Series Spicer MAINTENANCE FREE Universal Joint
Use this u-joint when you want the most strength out of a 1310 series universal joint. Stronger than a greaseable u-joint.
What are the dimensions of a 1350 U-joint?
|U-Joint Series||Width Center/Center||Currie Strap Kit P/N|
|1330 BC*||1.590 in.||CE-4059|
How do I know if I have a U-joint Spicer?
We recommend using a caliper or micrometer to most accurately measure u-joints. Once you have recorded your measurements, click on the images below to select the appropriate style of u-joint you have. You will then be directed to The Expert to identify your u-joint kit by the dimensions you recorded.
What is the difference between 1310 and 1350 U-joints?
Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.
How do you tell the difference between a 1310 and 1350 u-joint?
Take note that the u-joint is only as strong as the smallest series number. The 1310 to 1350 U-Joint Cross Width is 3.625 (3 5/8”) on the 1350 side and 3.250 (3 1/4”) on the 1310 side. The Cap diameters are different as well. 1 1/16″ on the 1310 side and 1 3/16″ on the 1350 side.
How are U-joints measured?
You will need to measure from the edge of one snap ring groove straight across to the edge of the other snap ring groove. For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap.
What size is a 1330 u-joint?
Driveshaft and Driveline Parts >
Universal Joints >
U-Joints BY SIZE >
1330 Series U-Joint 3.625 X 3.625 – 1.062 – 1.125 outside snap ring >
1.062 X 1.062 Bearing Cap Diameter.
How do I choose a u-joint?
How to measure yokes and u joints
Do they make U-joints with different size caps?
Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.
What is double cardan joint?
A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.
How much torque can 1310 U Joint handle?
According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.
How much drive shaft angle is too much?
Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.
What are the different types of U-joints?
There are two types of U-joints, the cross and roller type and the ball and trunnion type. The cross and roller type is used the most
it allows the drive shaft to bend. The ball and trunnion type less frequently used
it allows the drive shaft to bend and also permits backward and forward motion of the drive shaft.
What is a Spicer joint?
Super strong, super durable Spicer Extreme u-joints are meant for off-road use and slower speeds. Featuring an SAE-4340 nickel chromoly steel cross with an enlarged trunnion diameter for added strength, these u-joints are virtually indestructible.
How do you measure Hardy Spicer?
Identifying the Driveshaft Series and U-joints | Spicer Garage