Quick Answer

Quick Answer: What size is a 1350 on a yoke?

How much power can a 1310 U-joint handle?

According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.

What is a 1350 yoke?

The forged 1350 steel pinion yokes are designed for Spicer 1350 series universal joints, forged for maximum strength, precision machined, heat treated for toughness, built with U-joint-style joint retainers, and available with the appropriate nuts, washers and u-bolt.

What is the strongest U 1310 joint?

1310 Series Spicer MAINTENANCE FREE Universal Joint

Use this u-joint when you want the most strength out of a 1310 series universal joint. Stronger than a greaseable u-joint.

Are all 1310 U-joints the same?

This allows you to mate a larger (or smaller) U-joint to the other. For example, you buy a new driveshaft that comes with 1350 weld-in yokes, but your car has 1310-sized yokes for the transmission and rear differential.U-Joint Sizes.

Series Width Cap Diameter
7290 2.622 1.126″

How strong is a 1350 u-joint?

Relying on information provided by the manufacturer of the components, our calculation is that the 1350 series joint is about 37.5-percent stronger than the 1310 series. The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.

How do you tell the difference between a 1310 and 1350 u-joint?

Take note that the u-joint is only as strong as the smallest series number. The 1310 to 1350 U-Joint Cross Width is 3.625 (3 5/8”) on the 1350 side and 3.250 (3 1/4”) on the 1310 side. The Cap diameters are different as well. 1 1/16″ on the 1310 side and 1 3/16″ on the 1350 side.

What is the difference between 1330 and 1310 u-joint?

1330 joints use a larger body than the 1310 joint but the same-size trunnions and caps. They are often found in 3⁄4-ton trucks and allow more angularity than 1310 joints but are only marginally stronger. 1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

How do I know what size U joint?

For U-joints with outside snap rings, you will need to measure from the edge of one u-joint cap straight across to the edge of the other u-joint cap. With these dimensions, it will be easy to identify what series of U-joint that you have.

What is the yoke on an axle?

The slip yoke is an important component of any drive shaft assembly. The slip yoke assembly (pictured on the right) is what allows drive shafts and PTOs to flex or “slip” with their given application. The slip yoke is also essential for allowing u-joints to rotate properly with the drive shaft.

How do you measure a rear yoke?

How to measure yokes and u joints

How much drive shaft angle is too much?

Ideally, both driveshaft-operating angles will be 1 to 3 degrees. Anything over 3 degrees at the rear axle will shorten your universal joint’s life and could create vibration. If your angle is larger than 3 degrees, you must make sure not to exceed max driveshaft RPM as shown on this Spicer table.

What is AU joint Spicer?

Spicer Extreme™ U-Joints: for Off-Road Use Only

Featuring an SAE-4340 nickel chromoly steel cross with an enlarged trunnion diameter for added strength, these u-joints are virtually indestructible.

What is a 1344 u-joint?

QU40758 Greaseable S44, AAM 1344, or 3R Series Driveshaft Universal Joint for many Dodge and General Motors front or rear driveshafts from the mid 1970’s to current. QU40758 is a hot-forged, alloy steel, greaseable u-joint with nitrile rubber seals. You will find this u-joint used in both CV and non CV applications.

Where is Spicer made?

Spicer incorporated the Spicer Universal Joint Manufacturing Company in May 1905, shortening the name to Spicer Manufacturing Company in 1909. In 1910, the company relocated to a site adjacent to the Lehigh Valley Railroad and Bound Brook in South Plainfield, New Jersey.

How many u-joints do I need?

That’s why it’s a good idea to check the u-joints at every oil change. A typical rear wheel drive vehicle has 2 or 3 u-joints. Some vehicles with a long wheel base, such as buses, have 3 or more u-joints. The more u-joints a vehicle has, the higher the chance a u-joint will fail.

Does drive shaft diameter matter?

The longer and smaller (diameter) a driveshaft is, the lower its critical speed. Critical speed is felt as excessive vibration that could cause the unit to fail.

Do universal joints work at 90 degrees?

It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft. The universal joint is not a constant-velocity joint.

Do they make u-joints with different size caps?

Yes they do sell Ujoints with different size caps on each end. I had to use one when I bought a different driveshaft for a 1984 chevy truck that I had.

What series is a 369 u-joint?

Fitment U-Joint moog-369 fits these vehicles: AMC Ambassador 1967 thru 1974. AMC American 1968 thru 1968. AMC AMX 1968 thru 1980.

What is a CV driveshaft?

Constant Velocity, or CV drive shafts, are a unique type of drive shaft that allows for continual rotational velocity through a variable angle without a significant increase in friction or play. The most common applications for a CV drive shaft are: Front-wheel drive vehicles. All-wheel drive vehicles.

Is an axle the same as a drive shaft?

Location. The driveshaft runs down the center of a vehicle from the rear of the transmission to the rear differential gearbox and is visible beneath the vehicle. Axle shafts are concealed inside the steel rear-end housings running from the differential to each of the rear wheels.