Quick Answer

Quick Answer: What year is Dana 60 Super Duty?

Description. Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

How much HP can a Dana 60 take?

The Dana 60 can easily handle drivetrains producing 600 horsepower, and is commonly accepted as the strongest passenger car axle you can find. The Dana 60 is also quite adaptable. Just about any ring and pinion combination you want between 3.54:1 and 7.17:1 is still readily available.

Is a Dana 60 a 1 ton axle?

The Dana 60 and Dana 70 are two heavy-duty variants in the Dana axle line, and are typically found in 3/4 ton and 1 ton pickup trucks.

Is a Ford Dana 60 the same as a Chevy Dana 60?

There are three major variations of the Dana 60 axle used in the 1960s, 70s, and 80s: Dana 60 axles on the GMC, Chevy, and Jeep are all basically the same. Dodge and Ford Dana 60 axles are different.

What is the difference between a Dana 60 and a Super 60?

The Dana Super 60 is an upgraded version of the Dana 60 axle. Differences in the Dana Super 60 versus the regular Dana 60: Larger and thicker diameter steel tubes (3.75 inches diameter and ½ in thick) Larger ring and pinion which increase the contact area and overall strength.

What vehicles came with a Dana 60 front axle?

The Dana 60, a heavier-duty axle than the Dana 44, was first used in the 1950s. It was the axle of choice under countless Dodge, Ford, GM, Studebaker, IH and Jeep 3/4-ton and 1-ton fullsize trucks, as well as Ramchargers and Trail Dusters with the 440ci V-8, and some heavy-duty 1/2-ton Ford and IH trucks.

How much power can a Dana 70 handle?

Registered. They can handle 700hp+, yet can’t handle stock power… all depends on how it is used. The carrier in the 70 is the weakest link.

How much torque can a 14 bolt handle?

Found under ¾- and 1-ton GM trucks, vans and SUVs, the 14-bolt received a max torque rating of 6,242 pounds.

How much power can a Dana 80 handle?

The Dana 80 has a GAWR up to 11,000 pounds (5,000 kg), however it is common practice among manufacturers to derate Dana 80’s. Gross axle weight ratings are lowered by the vehicle manufacturer for safety and tire reasons.

Is Dana 44 better than 60?

Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.

What is a Dana Super 60?

The Dana super 60 is the front axel in a 4wd f450 or f550 and has 10 lugs, and is a few inches wider, equaling much better turning radius.

What’s the difference between a Dana 44 and a Dana 60?

The Dana 44 differential cover will measure about 9 1/2 inches wide and 10 1/2 inches tall, while the Dana 60 differential cover will measure about 11 1/4 inches wide and 12 inches tall. Beware: The Dana 70 differential cover measures the same as the Dana 60 cover.

What years did Ford use Dana 60 front axle?

Ford uses Dana Super 60 Front Driving Axles in 2005 and newer F250, F350, F450, and F550 Super Duty 4×4 trucks.

Are Dana 60 limited slip?

Nitro Power Lock Limited Slip for Dana 60-30 Spline

Nitro Gear &amp
Axle strives to provide the highest quality differential &amp
axle components available. We take the steps necessary to ensure our parts are dependable. Our product range is continually growing to meet the needs of consumers for new ratios and Fits.

What bolt pattern is a Dana 60?

The factory Dana 60 rears had 4.5″ bolt pattern . They were the only cars built by Mopar to have 2 different bolt pattern wheels .

What year is a Dana 60 kingpin?

The Kingpin Model 60 stayed in the Ford lineup as the only available front drive axle for the F-350 until the end of the 1991 model year. Ford switched to a ball joint Model 60 for the 1992 model year.

When did the F250 get a Dana 60?

The 1999 through 2003 model year F250/350 had Dana 50 Axles. The 2004 and up F250/350’s had Dana 60 axles.

What does a Dana 60 weight?

The Dana 60 is praised for its brute strength and full floating configuration, with the kingpin front axle being the “Crown Jewel” for off-road rigs. At 500 lbs, its biggest weakness is its sheer weight.

Do I have a Dana 60 front axle?

Many Dana axles have the model ID cast into the fins or centersection. Look for a “44” or “60” cast into the reinforcement ribs. The number can usually be found on the lower right side rib below the differential cover, but it may also be found on other ribs or on top of the main cast structure.

Are Dana 60 and 70 diff covers the same?

It can be very difficult to tell a Dana 60 from a Dana 70, as they have nearly identical covers with exactly the same bolt pattern. One way to tell if you have a Dana 60 or Dana 70 is to measure the cover flange height (yellow arrow). The Dana 60 flange height is approximately 1″ high.

What did a Dana 70 come in?

The Dana 70 rear axle was first used in the Dodge W300 in 1958. The Dana 70 started out using 10 spline pinions and 23 spline axle shafts. The later, more current, Dana 70 axles use 29 spline pinions and 32 or 35 spline axle shafts.

What does a Dana 80 come in?

ID A Dana 80 Rear Axle in Chevy, Dodge Ram, or Ford Truck IDN-126. Was: Dana 80 Rear Axles have been in production since the 1988 Model Year. They have been used in Chevy/GMC 1992-2002 , Dodge(1994-2002), and Ford (1988-current) trucks vans, and motorhome chassis.

Is a 14-bolt A 1 ton axle?

The 14-Bolt Is The Ford 9-Inch Of 1-Ton Trucks

Every diesel-powered pickup sold in the United States for the last 10 years has a full-floating rear axle.

What is the strongest rear end?

Dana 60 Rear End Assemblies

If you want a big brute of a rear end under your car, look no further than a Dana 60. Even in the heyday of muscle cars, Dana 60 rear differentials were renowned for their strength, along with their difficulty to locate.

What is a 14-bolt full floater?

Full-float axles have a tell-tale “axle end” that sticks out from the wheel surface. This is because the wheel hub on a full-float 14-bolt axle will stick out beyond the wheel mounting surface anywhere from about two to four inches. The full-float axle bolts to the end of the hub.

Is a Dana 80 a 1 ton axle?

The Dana 80 is only rated for 1 ton trucks, not a 2.5 ton truck.

Does RAM use Dana axles?

Axles. The Dodge Ram features a wide variety of axles. For the front axle of 4×4 Rams, a Dana 44 was used on all 1500 Rams and the early (light-duty) 2500 Rams. However, most of the 2500 and all 3500 Rams use Dana 60 front axles.

What is the difference between Dana 70 and 80?

According to several sources, a Dana 80 can have a Gross Axle Weight Rating (GAWR) of up to 11,000 pounds. A Dana 70 can have a weight rating of up to 10,000 pounds, but 8,000 pounds is much more common.