Quick Answer

What size are tie rod ends?

Simply put, there are two main sizes for tie rod ends, the studs which locate into either the pitman (steering) arm, or the spindles (steering knuckles) are of either an M10 or M12.

Is there a difference in tie rod ends?

Is it safe to assume that Tie Rods and Tie Rod Ends are the same things? Nope. The tie rod is the metal rod that the inner and outer tie rod ends thread onto. The inner connects to the steering rack and the outer has the ball joint that allows the wheels to turn.

What size is my tie rod?

The best and most accurate method for measuring the diameter of your tie rod is by using a precision measuring tool like a Slide Caliper. Slide Calipers work best for measuring the outside diameters of tie rods. They make digital, dial, and vernier calipers, all of which work fine.

How much torque does a tie rod need?

Outer tie rod jam nut: 25-37 ft-lb. Inner tie rod: 40-50 ft-lb. (Use 20mm open end wrench on flats to backup steering rack as you tighten the tie rod.)

Why are tie rod ends tapered?

A Case for Tie-Rod Ends

The tapered joint mates with the corresponding knuckle or steering arm, retaining a tight connection. The castle nuts with cotter pins add another layer of safety and minimize maintenance.

What is tie rod end?

Tie rod ends are a part of the steering system. Tie rods connect the spindle, on which your front wheel is mounted on one end, to the steering gear mechanism on the other end.

Do you need to grease new tie rod ends?

Some outer tie rods come with a grease fitting, which often come pre-greased and do not require any additional grease added when installed. However, make sure the grease fitting bolt is tightened during installation.

Which tie rod is inner or outer?

As the name states one is an Inner Tie Rod and is located on the inside of the Steering System. The Outer Tie Rod is located at the out side of the Steering System. The Outer Tie Rod is connected right at the Wheel and is the last link in the Steering System.

What do tie rods connect to?

Answer: Tie rods are an integral part of your vehicle’s steering. Just as its name suggests, a tie rod ties your vehicle’s steering rack to the steering arm. The steering arm is attached to the wheel. There are two types of steering systems: rack-and-pinion steering and re-circulating ball or mechanical steering.

How do you measure a rod end?

It is simply a count of the number of threads per inch measured along the length of the threaded rod. The diameter of the outer edge of thread represents the Thread Size. You are aiming for the same measurement location when measuring the diameter of a female rod end.

What thread are track rod ends?

1/2″ UNF.

Is a tie rod the same as a track rod?

Yes, a tie rod end is another name for a track rod end. Similarly, tie rod and track rod are the same thing. American English typically uses ‘tie rod’ and ‘tie rod end’, while British English uses ‘track rod’ and ‘track rod end’.

How do you seat a tie rod end?

How to Replace an Outer Tie Rod End

What do you torque ball joints to?

Many ball joints may have an initial torque spec as low as 15-30 ft/lbs and torque angles are between 140º and 225º.

Where is the inner tie rod?

Inner Tie Rod

The inner tie rods are pivot points and are attached to the end of the center link. It is located closer to the center line of the vehicle and is accordingly named “inner tie rod.” The inner tie rod is the first pivot point initiating the wheel to turn.

How long do heim joints last?

You are absolutely correct, dirt and moisture will kill heim joints, which is why major manufacturers don’t use them. They need the suspension to remain safe for 100,000+ miles in all conditions.

Are heim joints better than ball joints?

Ball joints are stronger than heim Joints in almost every way. Even oversized heim joints can’t keep up with a good ball joint. When it comes to strength, you have a lot more options with ball joints as well.

Who makes Johnny?

TMR Customs only sells genuine Johnny Joints from RockJock 4×4. The Johnny Joint was developed by John Currie as an alternative to traditional rod ends. Johnny Joints are known for their smooth ride and road manners – due to their polyurethane inserts.

How long do tie rod ends last?

Tie rods can last for years and years and some car owners may never have to replace them at all, but their longevity can be affected by certain driving conditions. Driving obstacles like potholes, poor road conditions or even minor accidents can cause tie rods to work incorrectly.

What happens when tie rod ends go bad?

When your tie rods go bad, the symptom you’re most likely to experience first is a vibration or shaking sensation in your steering wheel. You may also hear associated clunking and rattling noises, especially when turning the vehicle at low speeds. These sounds are caused by tie rods that are starting to wear out.

Can a tie rod break while driving?

If your tie rods break down completely while driving, it can be extremely dangerous—especially at high speeds—because you won’t be able to steer your car. Once you start noticing the symptoms of deteriorating tie rods, bring your car to a licensed auto mechanic for inspection as soon as possible.

What kind of grease do you use for tie-rod ends?

Mystik JT6 Hi-Temp Multi-Grease

This grease is more than capable for high-milage daily drivers and will keep components such as ball joints and tie rod ends well lubricated for a long time, through extreme conditions.

How often do tie rods need to be greased?

In most cases, you have to grease your u-joints every 5,000 miles or so. When you fail to service your u-joints on a regular basis, they will fail.

How do I lubricate my steering shaft?

The steering shaft passes through a rubber boot at the firewall. You will see it if you crawl under the dash. Spray some aerosol white lithium grease between the boot and shaft and the noise will go away. Make sure you get some grease all around the shaft and boot.

Is there a left and right tie rod end?

Yes, there are two different control arms.

Tie rods are the shafts that stick out of power steering rack and pinion assembly on either side of it.

How do you diagnose tie rod ends?

5 Signs that the Tie Rod Ends in Your Vehicle May Be Bad

  1. Inability To Steer.
  2. A Squealing Sound When You Turn.
  3. Uneven, Excessive Tire Wear.
  4. Misaligned Front End.
  5. A Steering Wheel that Feels Unusual.

Can inner tie rods cause vibration?

Vibration or Looseness in Steering Wheel

Because the tie rods link the steering wheel to the front wheels, steering problems can be a symptom of a loose or damaged tie rod. Common signs include a steering wheel that shakes or vibrates and looseness or excessive play in the steering wheel.