Quick Answer

Your Question What Dana axle is a 1 ton?

One thing that’s confusing about the Dana 60 axles is that a Dana 60 in front is usually considered a 1 ton axle, and a Dana 60 in the rear is usually considered a 3/4 ton axle.

How do I know if my axle is 1 ton?

To determine which one you have, check the number of splines your axle has. If it has 30 splines or less, then it’s a Dana 60 axle. If there are 33 or 35 splines, then you have a Dana 70 axle. If you have a 1994-2001 Dodge you may have a Dana 80 axle which also has 35 spline axle shafts.

What trucks still have a solid front axle?

Even though we are now down to just three new vehicle models available with a solid front axle in the U.S.—Jeep Wrangler, Ford Super Duty, and Ram heavy-duty trucks (four if you count the über-expensive Mercedes G-class)—we’re still huge proponents of the driven beam axle construction for off-road use.

Which axle is used in heavy-duty vehicles?

Full-Floating Axle: True to its name, this axle type effectively floats in place and maintains its position, thanks to two bearings. It’s designed to transmit driving torque only. Full-floating axles tend to work best for larger vehicles, such as heavy-duty trucks.

Is a 14-bolt A 1 ton axle?

The 14-Bolt Is The Ford 9-Inch Of 1-Ton Trucks

Every diesel-powered pickup sold in the United States for the last 10 years has a full-floating rear axle.

Is Dana 44 better than 60?

Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.

How do I identify my Dana front axle?

To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.

How do I identify a Dana 30 front axle?

Dana 30 Axle Identification

A Dana 30 cover will look like a rounded square. It should have 10 bolt holes and is 9 inches wide.

What is a Dana axle?

The Dana/Spicer Model 44 is an automotive axle manufactured by Dana Holding Corporation and is used extensively among automobile manufacturers and in the automotive aftermarket area as well. The Dana 44 was first manufactured in the 1940s and is still being manufactured today, both front and rear axle variants.

Does Ford make their own axles?

The Sterling axle plant is also home of the renowned Sterling 10.5 axle which has been underpinning Ford’s heavy duty trucks for over three decades.Products.

Components Vehicles
Rear Axles F-150, Super Duty, Expedition, Navigator, Mustang, Transit
Front Axles F-150, Expedition, Navigator

What is the best 4×4 of all time?

The 12 Most Capable 4x4s Ever Made

  • 1992-2006 Hummer H1.
  • 1985-95 Suzuki Samurai.
  • 1993-97 Land Rover Defender.
  • 2003-19 Jeep Wrangler Rubicon.
  • 1979-85 Toyota Trucks.
  • 2005-19 Dodge/Ram Power Wagon.
  • 1979-2018 Mercedes-Benz G-Wagen.
  • 2010-19 Ford F-150 SVT Raptor.

What’s better ifs or solid axle?

IFS is simply more civilized than a solid-axle suspension. Because the left and right wheels are not directly connected via a solid beam, there will be less head toss in the cab over rough terrain. The tires and wheels are free to move independently when they encounter obstacles.

What is full floating axle?

A full floating axle consists of a wheel hub assemble that is separate from the axle shaft. A spindle bolted to the axle tube supports the wheel hub by means of a pair of wheel bearings. Therefore, the weight of the vehicle and its cargo is transfered to the axle tube, rather than the axle shaft itself.

Does 2 axle mean 4WD?

Four-wheel drive, also called 4×4 (“four by four”) or 4WD, refers to a two-axled vehicle drivetrain capable of providing torque to all of its wheels simultaneously.

What does 2 axle mean?

Most cars have two axles. As a general rule of thumb, cars and trucks have 1 axle for every pair of wheels. These are referred to as “2-axle” vehicles, which encompasses most vehicles you’ll see on the road. Motorcycles also have two axles.

Is a 14 bolt rear end a 1 ton?

GM’s Strong &amp
Plentiful Axle

First appearing in 1973, the 14-bolt is one of the most used rear axles in the General Motors stable. Found under ¾- and 1-ton GM trucks, vans and SUVs, the 14-bolt received a max torque rating of 6,242 pounds.

What is a 14 bolt full floater?

Full-float axles have a tell-tale “axle end” that sticks out from the wheel surface. This is because the wheel hub on a full-float 14-bolt axle will stick out beyond the wheel mounting surface anywhere from about two to four inches. The full-float axle bolts to the end of the hub.

How do I identify a 14 bolt axle?

GM 14 Bolt Differential Explained – How to Identify

How big of a tire can a Dana 44 handle?

However, as a very general rule, a 36-inch tire is about the limit for a Dana 44.

What’s the difference between a Dana 30 and Dana 44?

The only difference between the JK Dana 30 and Dana 44 is ring gear size, electronic locker, and bigger shafts. (even if she insists shaft size doesn’t matter…) You’re better off just starting with an aftermarket Dana 44 that is a “true 44”.

How do you tell if you have a Dana 30 or 44?

The quickest way to tell is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle. On a Dana 44 Model, you will see a large castle nut threaded onto a ball joint. For Dana 30 Models, you will see a king pin cap with four bolts threaded down into the top of the knuckle.

What is Dana 30 axle?

The Dana/Spicer Model 30 is an automotive axle manufactured by Dana Holding Corporation. It has been manufactured as a beam axle and independent suspension axle with several versions.

What vehicles have a Dana 44 front axle?

The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of Jeeps, as well as International Harvester, Dodge, Studebaker and Ford trucks, and even under the rear of Isuzu Rodeos and Honda Passports up until the mid-’90s.

How do I know if I have a Dana differential?

Numbers. The Bill of Material (BOM) number is used to identify Dana differentials. The BOM will identify the model number, the gear ratio, the type of differential, and all component parts. Traditional BOM’s are 6 digits followed by 1 or 2 digits and start with the numbers 60 or 61.

Do I have a Dana 35 or 44?

There are a few things that can help you tell if the axle is a Dana 35 or a Dana 44. The easiest way to tell these axles apart is to look at the shape of the differential cover. The Dana 35 cover is pretty much perfectly round. The Dana 44 is sort of a six-sided shape.

Is a Dana 30 limited slip?

True-Trac limited slip for Dana 30 front. fits 3.73 and up. The True Trac limited slip uses a worm-gear design to bias torque from one tire to the other, providing extremely smooth operation. Since there are no clutches in this unit, there are no parts to wear out and no need to run limited slip additive in your oil.

What is Dana 35 axle?

The Dana/Spicer Model 35 is an automotive axle manufactured by Dana Holding Corporation since 1985 when American Motors (AMC) sold its axle tooling equipment to Dana. The axle was originally named an AMC-15 when it was first made in 1962.

What does the 44 mean in Dana 44?

44 is rated for 4,400 ft. lbs.
a 60 is rated for 6,000 ft. lbs. That’s max torque, continuous rated torque is quite a bit less. Load rating for a Dana 44 is 3,300 lbs.

Why are axles called Dana?

The first Dana axle was the 23 rear axle for CJ-2A Jeeps, produced from 1941. It was so named because it had a gross axle weight rating (GAWR) of 2,300 pounds.

How much torque can a Dana 80 handle?

It’s a full-float unit with 11.25-inch ring gear diameter
1.625-inch (minimum diameter) 37-spline pinion shaft
11/2-inch-diameter, 35-spline axleshafts
and a 4-inch axletube diameter. It has an 11,000-pound gross axle weight rating and a continuous manufacturer’s output torque rating of 2,500 lb-ft.