Quick Answer

Your Question What is a 1310 CV yoke?

1310 CV Style Yoke for the Front &amp
Rear output of the Dana 300 T-cases with 26 spline outputs
. These yokes are needed to run a Dual Cardan (CV) shaft like the ones we sell here on our website. Spline Count: 26. Spline Diameter: 1.146. Hub Diameter: 1.552.

What is a 1350 slip yoke?

When strengthening your GM driveline a forged steel slip yoke is a very important component. A slip yoke is what allows the driveshaft to “slip” a small amount into the transmission. Its is also essential for allowing u joints to rotate properly with the drive shaft.

What is the yoke on a transfer case?

The slip yoke is present to transfer power from your Jeep’s transfer case to the driveshaft, sliding in and out of the transfer case. This sliding capability allows for changing length depending on the vehicle’s movements.

What is a non CV yoke?

This 1350 Non-CV yoke is for NVG241OR transfer cases NOT equipped with a speed sensor mounted in the tailhousing. This new yoke uses U-bolts instead of problematic straps and can be used on the front or rear output shaft.

What is double cardan joint?

A Double Cardan joint is essentially two single Cardan joints connected by a coupling yoke that contains a centreing mechanism. This centering mechanism keeps the input and output shafts in the same plane, regardless of the operating angle.

How much is a custom drive shaft?

How much does a custom driveshaft cost? Our custom made driveshaft costs are based on the materials that go into them. PST Driveshafts can range from $350 up to $1,500 depending on the strength and materials.

Where is the yoke on a transmission?

The slip yoke is the part of your driveshaft that connects the driveshaft to the output shaft on your transfer case or transmission.

How do you remove yoke from transfer case?

Using a HOMEMADE YOKE PULLER to Remove a Jeep CJ5 Transfer …

Where is the yoke on a truck?

Driveshaft yokes are located on the ends of the driveshaft. In most configurations, one yoke connects to the rear of the vehicle while the other yoke reaches into the transmission. The driveshaft sends power from the transmission and turns the differential, which moves the wheels.

What size is a 1310 u-joint?

Understanding U-Joints

Series Cross Width Cap Diameter
1310 3.219 (3 7/32”) 1.062 (1 1/16”)
1310BC* 3.219 (3 7/32”) 2 @1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)
1330 3.625 (3 5/8”) 1.062 (1 1/16”)
1330BC* 3.625 (3 5/8”) 2 @ 1.062 (1 1/16”) 2 @ 1.125 (1 1/8”)

What series is a 369 u-joint?

Fitment U-Joint moog-369 fits these vehicles: AMC Ambassador 1967 thru 1974. AMC American 1968 thru 1968. AMC AMX 1968 thru 1980.

What is a CV driveshaft?

Constant Velocity, or CV drive shafts, are a unique type of drive shaft that allows for continual rotational velocity through a variable angle without a significant increase in friction or play. The most common applications for a CV drive shaft are: Front-wheel drive vehicles. All-wheel drive vehicles.

Are aluminum driveshafts strong?

And because it’s very strong. Speaking in terms of weight, an aluminum driveshaft is about 1.5 pounds per foot lighter than a steel-based shaft using a 3.5-inch diameter shaft, as an example.

Are carbon fiber driveshafts good?

After use and testing of those three types though the years, a carbon-fiber shaft is the best and safest way to go. When a steel or aluminum driveshaft fails, damage can be costly (motor, trans, rear axle, exhaust, body) and injuries to the driver can occur.

How do you measure a custom drive shaft?

How To Measure for a Driveshaft

  1. End yoke to end yoke (Measure from the center of one U-Joint to the center of the other U-Joint)
  2. Spline to end yoke (Measure from the tip of the spline to the center of the U-Joint)
  3. Flange to flange (Measure from the face of the first flange to the face of the 2nd Flange)

How do I know what slip yoke I need?

Measure OE slip yoke with a precision tool to determine which yoke you need. length, journal size &amp
U-joint series are critical dimensions requiring accurate measurement. Some slip yokes have missing splines – include the missing spline in your count or count the splines on the transmission output shaft to be accurate.

What is the yolk on a driveshaft?

A yoke is a device that unites, couples, or connects. As it relates to driveshafts, a yoke is the basic torque input and output component. The yokes illustrated in Figures 9 and 10 are “tube or weld yokes”. A tube or weld yoke is a yoke incorporating a locating diameter that aligns a tube or other driveshaft member.

How do you measure a driveshaft yoke?

Place one end of the tape measure near the tip of the slip yoke. Place the other end of the tape measure near the middle of the slip yoke’s u-joint. Note the measurement on the tape measure to determine the length of the slip yoke.

How do you remove a yoke bolt?

how to loosen a frozen bolt on a driveshaft yoke

How do you pull a pinion yoke?

How to Replace Pinion Seal &amp
Yoke 1994-2004 Chevy S-10

What are the parts on a drive shaft?

The drive shaft has the following major components:

  • Tube.
  • Flanges.
  • Centre bearing.
  • Slip yoke and Tube yoke.
  • Universal joint.
  • End yoke.
  • Midship shaft.

What is a slip yoke on a truck?

The slip yoke is an important component of any drive shaft assembly. The slip yoke assembly (pictured on the right) is what allows drive shafts and PTOs to flex or “slip” with their given application. The slip yoke is also essential for allowing u-joints to rotate properly with the drive shaft.

What are the ends of a drive shaft called?

Glossary of Common Driveshaft Terms

Bearing Plate A retainer plate fixed to the back of a round bearing used to position the bearing in the yoke.
End Yoke A yoke which attaches a driveshaft to another drive train component such as the transmission.